Vergleich

RhoA G-LISA Activation Assay (luminescence)

Hersteller Cytoskeleton
Kategorie
Typ Assay
Specific against other
Menge KIT 96 assays
ArtNr BK121
eClass 6.1 32161000
eClass 9.0 32161000
Lieferbar
Additional info

Product Uses Include

  • Rho signaling pathway studies
  • Rho activation assays with primary cells
  • Studies of Rho activators and inactivators
  • Rho activation assays with limited material
  • High throughput screens for Rho activation

Introduction
This G-LISA Rho activation assay measures the levels of GTP-loaded RhoA in cells. The level of activation is measured with luminometry. The G-LISA Rho activation assays are ELISA based Rho activation assays with wich you can measure Rho activity in cells in less than 3 h. For a more detailed introduction on G-LISA assays and a listing of other available G-LISA kits, see our main G-LISA page. For a kit to measure RhoA activation with colorimetric detection, see Cat. # BK124

Kit contents
The kit contains sufficient reagents to perform 96 Rho activation assays. Since the Rho-GTP affinity wells are supplied as strips and the strips can be broken into smaller pieces, each kit can be used for anywhere from one to multiple assays. The following components are included in the kit:

  1. 96 Rho-GTP affinity wells
  2. Lysis buffer
  3. Binding buffer
  4. Antigen presenting buffer
  5. Wash buffer
  6. Antibody dilution buffer
  7. Anti-RhoA antibody
  8. HRP-labeled secondary antibody
  9. Positive control RhoA protein
  10. Protease inhibitor cocktail (Cat. # PIC02)
  11. Luminescence detection reagents
  12. Precision Red Advanced protein assay reagent (Cat. # ADV02)
  13. Manual with detailed protocols and extensive troubleshooting guide

Equipment needed

  1. Luminometer capable of reading a 96-well plate
  2. Multichannel or multidispensing pipettor
  3. Orbital microplate shaker capable of at least 200 rpm shaking (400 rpm is optimal)

Example results
Serum starved Swiss 3T3, HeLa and A431 cells were stimulated with the Rho activating compound lysophosphatidic acid and RhoA activation was measured with BK121 (Fig 1)

Figure 1. Rho activation by lysophosphatidic acid (LPA) measured by G-LISA kit BK121. Swiss 3T3 (mouse), A431 (human) and HeLa (human) cells were serum starved followed by stimulation by LPA. 25 ug of lysates were subjected to the G-LISA assay. Data shown are relative luminescence units (RLU) over background signal (wells incubated with lysis buffer alone instead of cell lysates). Numbers above LPA bars correspond to fold activation compared to the control serum starved samples.

Go to main G-LISA page

G-LISA Products:
Cdc42 G-LISA Activation Assay, colorimetric format (Cat.# BK127)
Rac1 G-LISA Activation Assay, luminescence format (Cat.# BK126)
Rac1, 2, 3 G-LISA Activation Assay, colorimetric format (Cat.# BK125)
RhoA G-LISA Activation Assay, colorimetric format (Cat.# BK124)

Associated Products:a
Anti-Cdc42 monoclonal antibody (Cat.# ACD03)
Anti-Rac1 monoclonal antibody (Cat.# ARC03)
Anti-RhoA monoclonal antibody (Cat.# ARH03)

Delivery Time
1-2 Weeks
Shipping Temp.
AT
Storage on Arrival
4C
faqs

Question 1:  There is less than a 2-fold difference in signal intensity between my positive control and lysis buffer blank.  Why?

Answer 1:  To accurately measure luminescence signal intensity between the positive control and buffer blank, please check the instrument settings on the luminometer (see below for suggestions).  We also recommend running some &ldquo, set-up&rdquo, experiments with just the buffer blank and positive control to determine optimal settings for detecting the positive control signal 3-5 fold higher than the buffer blank.  It is also important to remember to use a fresh control protein tube for each run of positive control samples.  Do not store and re-use the positive control.

Machine Settings

  Gain  

Gain controls the sensitivity of the machine.  Most luminometers do not allow manual alteration of gain and use an auto-calibration or limited calibration function.  Turn off auto-settings and auto-calibration to use the machine in manual mode.  It is important to contact the luminometer manufacturer or consult the user&rsquo, s manual to determine the best way to alter the machine sensitivity.  If gain can be altered, one should read at low, medium and high gains to determine the reading within the linear range of the assay (positive control should be 3-5X higher than blank). Gain range varies with instrument.  For example, gain in the Tecan GmbH SpectroFluor Plus ranges from 0 - 150 (where 150 is the highest).

  Integration Time

This parameter can be varied on most machines.  It is a good idea to set the machine at the lowest integration time (usually 10 &ndash, 100 ms). Integration times greater than 200 ms are likely to read out of the linear range of the assay and may require lowering of gain or dilution of primary and/or secondary antibodies.

  Shaking

Most machines give the shaking option.  The recommended setting is 5 sec shake, medium orbital speed before read.   This option is not essential to the assay.

  Temperature

Room temperature

  Plate type

Any setting that specifies 96 well flat, white will be sufficient.

  Filters

Luminescence does not require excitation or emission filters so the filter spaces should be left blank.  If this is not an option, excitation can be set at any value and emission should be set between 400-500nm, with 430-445 as optimal setting.

 

Question 2:  My arbitrary luminescence units (ALU) or relative luminescence units (RLU) are very different from what is depicted in the manual.  Why?

Answer 2:  This is very typical as the luminescence units will vary from luminometer to luminometer based on the machine&rsquo, s sensitivity and instrument settings.  The important information to take note of is what the relationship is between buffer blank and positive control luminescence values.  The positive control signal should be 3-5 fold greater than the buffer blank luminescence signal.  If that is the case, then the G-LISA assay is functioning in the linear range and experimental samples can now be processed.

 

If you have any questions concerning this product, please contact our Technical Service department at infohoelzel.de.

Hinweis: Die dargestellten Informationen und Dokumente (Bedienungsanleitung, Produktdatenblatt, Sicherheitsdatenblatt und Analysezertifikat) entsprechen unserem letzten Update und sollten lediglich der Orientierung dienen. Wir übernehmen keine Garantie für die Aktualität. Für spezifische Anforderungen bitten wir Sie, uns eine Anfrage zu stellen.

Alle Produkte sind nur für Forschungszwecke bestimmt. Nicht für den menschlichen, tierärztlichen oder therapeutischen Gebrauch.

Menge: KIT 96 assays
Lieferbar: In stock
lieferbar

Lieferung vsl. bis 18.04.2024 

Vergleichen

Auf den Wunschzettel

Angebot anfordern

Lieferzeit anfragen

Technische Frage stellen

Bulk-Anfrage stellen

Fragen zum Produkt?