Vergleich

Actin protein (pyrene, rabbit skeletal muscle)

Hersteller Cytoskeleton
Kategorie
Typ Proteins
Specific against Rabbit
Menge 1 x 1 mg
ArtNr AP05-A
eClass 6.1 34160400
eClass 9.0 42020190
Lieferbar
Additional info

Product Uses Include

  • Studying actin polymerization in vitro.
  • Studying the effects of actin binding proteins and drugs on actin polymerization in vitro.

Material
Purified rabbit muscle actin (Cat. # AKL99) has been modified to contain covalently linked pyrene at the cysteine 374 residue. An N-(1-pyrene) iodoacetamide is used to label the actin protein. Pyrene labeling stoichiometry has been determined to be 0.6 dyes per actin monomer. Pyrene labeled rabbit muscle actin has an approximate molecular weight of 43 kDa, and is supplied as a white lyophilized powder. The lyophilized protein is st able for 6 months when stored desiccated to < 10% humidity at 4C. The protein should be reconstituted to 20 mg/ml with distilled water; it will then be in the following buffer: 5 mM Tris-HCl pH 8.0, 0.2 mM CaCl2 0.2 mM ATP, 5% sucrose, and 1% dextran.

Purity
Protein purity is determined by scanning densitometry of Coomassie Blue stained protein on a 4-20% gradient polyacrylamide gel. Pyrene muscle actin is > 99% pure (see Figure 1).

Figure 1. Pyrene Muscle Actin Protein Purity Determination. A 100 ug sample of pyrene muscle actin (molecular weight approx. 43 kDa) was separated by electrophoresis in a 4-20% SDS-PAGE system, and stained with Coomassie Blue. Protein quantitation was determined with the Precision Red Protein Assay Reagent (Cat. # ADV02).

Biological Activity
The fluorescent signal of monomer pyrene actin is enhanced during its polymerization into filaments, making it an ideal tool for monitoring actin filament formation. Stringent quality control ensures that AP05 pyrene F-actin has a 7-12 fold fluorescent enhancement over non-polymerized pyrene G-actin (See Fig 2).

Figure 2. Fluorescence enhancement during pyrene actin polymerization. Pyrene muscle actin was polymerized in duplicate wells of a 96-well plate by the addition of Actin Polymerization Buffer (Cat. # BSA02). The fluorescent signal was scanned every 30 s for 1 h. Polymerized pyrene F-actin shows a 10 fold fluorescent enhancement over non-polymerized pyrene G-actin and buffer control.

Delivery Time
1-2 Weeks
Shipping Temp.
AT
Storage on Arrival
4C
faqs

  Question 1:  When performing the polymerization assay using pyrene-labeled actin (Cat. # AP05), the fluorescence signal of the globular actin in G-buffer increased over time, so that the 0 value was already rather high. 

Answer 1:  After preparing actin at a concentration of 0.4 mg/ml for polymerization (from either fresh stocks or frozen aliquots), it is important to incubate the actin on ice for 1 hour to depolymerize any actin polymers that might have formed during storage.  For an even cleaner sample of G-actin, the samples can be centrifuged (100, 000 x g) for 60 min to absolutely insure the removal of residual actin oligomers and nucleating centers.  After centrifugation, use the top 80% of the supernatant as your G-actin stock.  This will eliminate any changes in fluorescence signal associated with G-actin.

 

Question 2:  During my polymerization reaction, the growth phase and steady-state levels of F-actin produced are lower than what is shown in the manual.  Why?

Answer 2: One of the most common causes of reduced fluorescence intensity signal is non-optimal machine settings.  Please check that the machine&rsquo, s settings are similar to these:

  Measurement type:  Kinetic 120 cycles, 60 sec interval time

Fluorescence wavelengths:   Ex. 350 or 360 +/- 20 nm

  Em. 407 or 410 +/- 10 nm or 420 +/- 20 nm

Gain:   100 (on a scale of 0-120, where 120 is the highest)

Reads per well:   1

Fluorescence reading from:   Top

Also, when samples are not being measured in the fluorimeter, the excitation beam should be shuttered to prevent the beam from bleaching the pyrene fluorescence.  When measuring the fluorescence, the shutter should be opened for no longer than 7 sec every 30 sec for 1 h.

 

If you have any questions concerning this product, please contact our Technical Service department at infohoelzel.de.

Hinweis: Die dargestellten Informationen und Dokumente (Bedienungsanleitung, Produktdatenblatt, Sicherheitsdatenblatt und Analysezertifikat) entsprechen unserem letzten Update und sollten lediglich der Orientierung dienen. Wir übernehmen keine Garantie für die Aktualität. Für spezifische Anforderungen bitten wir Sie, uns eine Anfrage zu stellen.

Alle Produkte sind nur für Forschungszwecke bestimmt. Nicht für den menschlichen, tierärztlichen oder therapeutischen Gebrauch.

Menge: 1 x 1 mg
Lieferbar: In stock
lieferbar

Lieferung vsl. bis 18.04.2024 

Vergleichen

Auf den Wunschzettel

Angebot anfordern

Lieferzeit anfragen

Technische Frage stellen

Bulk-Anfrage stellen

Fragen zum Produkt?