Actin Binding Protein Spin-Down Assay Kit (Non-muscle)

Hersteller Cytoskeleton
Typ Assay
Specific against other
Menge KIT 30-100 assays
ArtNr BK013
eClass 6.1 32161000
eClass 9.0 32161000
Delivery Time
1-2 Weeks
Shipping Temp.
Storage on Arrival

Wolter et al., 2012. GAS2L3, a novel target gene of the dream complex, is required for proper cytokinesis and genomic stability. J. Cell Sci. doi: 10.1242/Ÿ??jcs.097253.

Marat et al., 2012. Connecdenn 3/DENND1C binds actin linking Rab35 activation to the actin cytoskeleton. Mol. Biol. Cell. v 23, pp 163-175.

Trulsson et al., 2011. HAMLET Binding to a-Actinin Facilitates Tumor Cell Detachment. PLoS ONE. 6: e17179.

Gohla et al., 2005. Chronophin, a novel HAD-type serine protein phosphatase, regulates cofilin-dependent actin dynamics. Nat. Cell Biol. v 7, pp 21-29.

Falcon-Perez et al., 2002. BLOC-1, a novel complex containing the pallidin and muted proteins involved in the biogenesis of melanosomes and platelet-dense granules. J. Biol. Chem. v 277, pp 28191-28199.

Zhai et al., 2001. Tyrosine phosphorylation of villin regulates the organization of the actin cytoskeleton. J. Biol. Chem. v 276, pp 36163-36167.

Leung et al., 1999. Microtubule actin cross-linking factor (MACF): a hybrid of dystonin and dystrophin that can interact with the actin and microtubule cytoskeletons. J. Cell Biol. v 147, pp 1275-1286.


Question 1:  What are optimal conditions for preparing my actin binding test protein when using the non-muscle Actin Binding Protein Biochem Kit (Cat. # BK013 or muscle Actin Binding Protein Biochem Kit Cat. # BK001)?

Answer 1:  Make the test protein at the highest possible concentration in an actin compatible buffer such as a HEPES or phosphate buffer.  The high concentration (preferably >, 20 &mu, M) is necessary to optimize the opportunity to detect interactions between actin and the test protein.  In some cases the Kd (dissociation constant) of an actin binding protein/actin interaction may be so low as not to be detectable by protein assay of the pellet, however, the affect on the actin in the reaction mix may be enough to be detected by differences in the amount of actin in the pellet and supernatant versus the negative control.  We also recommend centrifuging the test protein at 150, 000 x g for 1 h at 4°, C to remove denatured proteins and cellular debris.  This is not necessary if other steps (e.g., affinity column purification) have been taken to purify the test protein.  After the high-speed centrifugation, remove the supernatant and place on ice.  This is the test protein stock.


The total ionic strength should be below 50 mM, this is due to the character of actin association whereby it&rsquo, s mainly ionic and hence will be affected by medium and high salt buffers. A good starting buffer is 20 mM Hepes pH 7.4 plus 20 mM KCl, plus protease inhibitors, phosphatase inhibitors and any co-factors that are necessary. A low salt actin polymerization 10x buffer can be made with 20 mM MgCl2 and 10 mM ATP thus allowing the salt to be kept low in the final reaction. 


Additional issues to consider are that a (i) test protein cofactor may be necessary, (ii) a factor in the assay could be actively inhibiting interactions, (iii) the test protein could have a preference for a different type of actin, or (iv) the test protein may be at a low concentration in tissue extracts.


To address some of these potential problems, reagents can be added to remove inhibitors, such as EGTA (Part #BSEG-01) for calcium.  In the case of motor proteins, the ATP/Mg2+ combination will dissociate the motor from the F-actin hence a non-hydrolyzable analog such as AMPPNP is used at 1 mM.  An actin affinity column can be used to concentrate and isolate more of the test protein.  Finally, different pH conditions may improve binding between the actin and actin binding protein (e.g. alpha-actinin&rsquo, s pH optima is 7.0).


Question 2:  Can the non-muscle Actin Binding Protein Biochem Kit (Cat. # BK013) be used to determine binding affinities between non-muscle actin and actin binding proteins?

Answer 2:  Binding affinity (Kd) can be estimated from the spin-down assay by titrating the test protein concentration between 0.2 and 20 &mu, M and finding the concentration where half the original protein is in the pellet. Plot percent test protein bound versus original concentration in the reaction to obtain the Kd in µ, M.


Question 3:  Can cell lysates be used with the non-muscle Actin Binding Protein Biochem Kit (Cat. # BK013) as the source of a test protein?

Answer 3: Yes, cell lysates can be used as the source of the test protein.  However, Cytoskeleton does not recommend this as the purity and concentration of the protein will often be too low to interact with actin.  Also, the lysates will contain additional accessory proteins and multiple phosphatases and proteases that can interfere or alter the interactions between actin and actin binding proteins.  If lysates are to be used, we recommend the following:


Although this kit is designed for use with pure proteins or compounds, some researchers have added extracts with good results. Generally researchers use over-expressed proteins and a wild-type control extract similarly over-expressed. It is necessary to make a 10 mg/ml protein extract and then use 1/3rd volume of this to 2/3rd volume of actin at 1 mg/ml.  In this way there is a high enough concentration of protein to indicate binding. The extraction buffer should be 20 mM Hepes buffer pH 7.4, 20 mM NaCl, plus any co-factors for the protein, and a protease inhibitor cocktail such as Cat. # PIC02.  Phosphatase inhibitors can also be added.  Rinse the cells with an ice cold buffer and lyse cells with a 25g bent over syringe needle or other device.  The pH can alter F-actin binding properties of actin binding proteins (ABPs) by 0 to 100%.   It is a good idea to test pH 6.5, 7.5, and 8.5 for extract preparation.  The control cell line is very critical because potential ABPs could appear in the pellet by other routes, for example, denaturing or aggregation with other cellular proteins.  The total ionic strength should be kept below 50 mM in order not to salt off any potential ABPs.

Hinweis: Die dargestellten Informationen und Dokumente (Bedienungsanleitung, Produktdatenblatt und Sicherheitsdatenblatt) entsprechen unserem letzten Update und sollten lediglich der Orientierung dienen. Wir übernehmen keine Garantie für die Aktualität. Für spezifische Anforderungen bitten wir Sie, uns eine Anfrage zu stellen.

Menge: KIT 30-100 assays
Lieferbar: In stock
Listenpreis: 898,26 €
Preis: 898,26 €


Angebot anfordern

Fragen zum Produkt?